If you need to cool two rooms, and there is only one place for the outdoor unit, the best engineering solution will be a split system for 2 rooms - the equipment is especially important for new high-rise buildings, where the facade parts decorated with special baskets are allocated for air conditioners.
What is the principle of operation of the “double” split, what are the advantages and disadvantages of the circuit, and also how much does such a system cost - we will consider in the article. In addition, we identified the main parameters for choosing an air conditioner, described the specifics of its installation and maintenance.
The relevance of a “dual” split system
In the private sector, there is usually no problem installing multiple devices for different rooms. But if the owner does not want to spoil the facade with several bulky boxes, it also makes sense to consider multi-split.
Business class high-rise buildings are equipped with centralized systems, so the issue of air conditioning a single apartment is removed. In other cases, the installation of HVAC equipment must comply with certain rules.
The dimensions of the installed suspended blocks, for example, channel or cassette systems, are limited by the height of the ceilings. A quota has been set for the total energy consumption in the apartment, which regulates the power of the supplied electricity. But most of the rules apply to external blocks.
In Europe, outdoor units have long been mounted on roofs or displayed on the inside of the courtyard, which preserves the aesthetics of the facades
On the facade and on the outside of some buildings, the installation of HVAC equipment is prohibited by law or individual operating regulations. But tenants are offered allocated places for such purposes on the balcony, roof, technical floor, in special niches.
On small sites, square meters is not enough. One apartment is usually allocated only one place measuring about 60 cm by 1.5 m. The most appropriate solution in this case will be to install a simplified multi-split system.
The principle of operation of the equipment
What is the difference between such a split system when compared with a conventional air conditioner? A feature is the triple separation of the freon circuit.
First part located in the external unit and consists of a compressor, flow dividers, condenser heat exchanger. The latter has 2 sections.
The compressor is forced to work continuously, even if one external unit is turned on, therefore more reliable elements with a margin of resource (+) are installed in such systems
The other two parts placed in indoor units and consist of evaporators and capillary tubes. All participants in the scheme are combined with each other by freon highways.
The operation of this circuit is based on the property of liquids capable of absorbing heat during evaporation, but during condensation, on the contrary, to release it. The agent in refrigeration systems is freon, which circulates in the circuit.
Heat is absorbed by the indoor units and sent to the outside due to the thermodynamics of the transition of the agent from liquid to gas and vice versa.
Hot freon leaves the compressor under pressure and runs into a separator, where it bifurcates to cool two rooms. Once in the evaporator, Freon will make the transition to a state of gas. Why does he take heat from room air, which is pumped by a fan.
Then freon goes to the condenser heat exchanger (also 2 sections), where it is cooled to a liquid state.
Thus, the process of cooling the premises occurs. But the equipment is able to work on heating. In this case, the direction of movement of freon changes.
Features of the operation of air conditioners
It is technically possible to connect up to 7 internal boxes to one external box. There are no clear links between the power of the outdoor unit and the number of indoor ones. One external can work in the company with both two and three internal.
When calculating the circuit, proceed from the total power of all indoor units, which should fit into the range of min and max values of the outdoor cooling capacity (+)
Conventional multi-splits differ from expensive and advanced multi-zone installations by the inability to operate indoor units in a “heat - cold” pair.
They know how to function in only one climatic direction - either everything is cold, or everything is warm. If you turn on the blocks in opposite modes, the equipment will not start.
But you can set a different temperature on each of the devices. But you need to stay within one regime - either cooling or heating.
We select the installation according to the characteristics
It is believed that a double split system should cost less than two separate devices, but this is not so. Compared to the total price of two units, one double will be 15-30% more expensive, even with the same power. The reason is the invertor principle of operation.
Inverter models use advanced technologies plus all kinds of upgrades that you will not find in conventional devices, which makes the system as a whole more expensive (+)
Non-inverter air conditioners are cheaper and can be equipped with a winter kit. But in the assortment line of manufacturers there are few such equipment due to low demand.
Three types of indoor units
It is possible to connect the internal modules of cassette, channel or wall type to the external block. Consider when and in which rooms they are used.
Cassette unit not suitable for rooms with low ceilings and / or small area. These models are designed for large commercial premises - offices, restaurants, shops, cinemas.
To install a cassette unit, 25-40 cm of inter-ceiling space is needed, and laying all communications requires high labor costs and sufficient skills of performers
Channel wiring also involves reducing the height of the rooms. This option is the most aesthetic, albeit expensive.
It will be appropriate in a country cottage, but not for two rooms, but for several rooms. You can make a general wiring with one or two external units.
The channel system is ideal if there are increased requirements for the design of the premises and there are no problems with the low height of the ceilings. Only decorative grills remain in the visible part
Wall blocks - The optimal solution for an ordinary apartment or house with standard ceilings. They are easy to install and do not require large rooms.
Technical parameters of devices
External blocks in dual split systems are more reliable and the total length of the tracks they have more when compared with conventional.
Indoor units are selected by:
- power;
- outdoor temperature range;
- feature set;
- length of communications;
- appearance.
The main functional parameter is the range of outdoor temperatures. It is important that the equipment operates in conditions that are below the maximum permissible. The efficiency of the equipment depends on atmospheric loading.
It is also important to consider the following three parameters:
- Amendments to additional heat gain. Often, these coefficients need different indoor units for different rooms.
- Outside Power, which should be equal to the total cooling capacity of the indoor units plus correction factors. In this case, the outdoor unit may have 3 or 4 ports for connecting freon pipelines, but only 2 are needed.
- Measurements of the maximum length of all freon pipelines to indoor units: each individually and the total number.
The disadvantages of the design include the need to install indoor appliances close to each other - in the neighborhood. The distance depends on the length of the track in the selected model.
When calculating the power of one indoor unit, we act like with a conventional air conditioner: we repel from the area of the room and the height of the ceilings. Then we sum these indicators to get the power of the outdoor unit (+)
There is also a simplified formula: at 10 m2 need about 1000 watts of power. This calculation works for rooms with good thermal insulation. If light enters the room from the south or south-west side, we add another 25% to the indicators.
Detailed instructions for calculating the power of a split are presented in this article.
Manufacturers and models
The most reliable manufacturers are traditionally considered Japanese firms Fujitsu, Mitsubishi, Toshiba. They are also the most expensive brands.
The middle price category is Chinese General climate and japanese Daikin. Budget Series - Chinese Hisense, English-Chinese Dantex.
Of the models for 2 rooms, you can consider the following:
- Mitsubishi Electric MSZ-HJ25VA-ER1 × 2 / MXZ-2HJ40VA-ER1: at 50 m2 with a deodorizing and anti-allergenic filter, low noise level of 20 dB, night mode.
- General Climate GC-M2E18HRN1: at 53 m2, there is a ventilation mode, self-diagnosis, drainage, but there are no fine filters.
- Electrolux EACS / I-07HP + EACO / I-14 FMI-2: at 40 m2, economical energy consumption, heating works at temperatures up to –15 degrees.
- Fujitsu Inverter AOYG14LAC2: an external unit that can be understaffed with low-cost internal ASYG07LMCA (15 m2) or designed for a large area ASYG07LUCA (20 m2) and ASYG09LUCA (25 m2).
- Hisense AMW2-20U4SNC1 / AMS-09UR4SVEDB6x2: at 50 m2, two-way connection of condensate drain is provided.
- Dantex RK-2M24SEGE: at 70 m2, there is a system against the formation of ice, but it works for heating at temperatures up to –7 ° С.
In assortment lines there are fixed and typesetting systems. The first imply a complete set from the manufacturer. In the second case, you can choose the blocks yourself.
Fixed are convenient if it is supposed to service the same premises (minor deviations are acceptable). Typesetting is relevant in reverse cases with rooms of different sizes
Specificity of installation and operation
If we compare the cost of installing two separate air conditioners and a double split system, the amount will be approximately the same. The reason is a similar length of tracks. The installation price directly depends on the length of inter-unit connections, cable, freon tubes.
During installation, it should be borne in mind that the freon bypass control system requires accurate accounting of the amount of substance for each of the indoor units
When the installation of the air conditioner is carried out in conditions of general repair, it is advisable to split the installation of the split system into 2 stages.
First, wall the walls, lay the inter-unit communications, fix the outdoor unit, and do indoor equipment after finishing the premises.
If installation is carried out after repair, freon pipelines are sewn up in special channels. They are not hidden in the walls, but it makes replacement easier if such a need arises in case of breakage or the desire to install more powerful equipment
It is better to place the outdoor unit on the facade under the window so that the master has access to it during maintenance.
Operational features of a split system:
- The outdoor unit operates at full power, even if the air conditioner is turned on in only one room. This increases energy consumption per instrument.
- At the same time, two devices cannot work for heat and cold. But if the system supports the ventilation mode, you can turn on the heating in one room and set the ventilation in another.
- If one outdoor unit breaks down without an air conditioner, two rooms will remain at once.
Indoor units, regardless of their number, need to arrange periodic sanitary services.
Mold on the fins of the evaporator and fan turbines halves the performance of the device, contributes to the appearance of an unpleasant smell.
What is multi-split. Block layout. Features of installation work.
Installing the system in 2 stages - before and after repair.
If there is no possibility or desire to install two separate air conditioners, it makes sense to choose a split system for two rooms. Important parameters when choosing - power, temperature range, the length of the freon conduits, elevations between the blocks.
Share with your readers your experience of choosing and using a split system in two rooms. Please leave comments, ask questions about the topic of the article and participate in discussions - the feedback form is located below.