The creation of a modern in-house electrical network is a responsible event related to calculations, the selection of wires and electrical installations, installation work. In this case, one of the main tasks remains to ensure the safety of residents and the safety of property. Do you agree?
If the protective devices are correctly selected and the connection diagram of the RCD and automatic devices is thought out, all risks are reduced to a minimum. But how to do that? What to consider when choosing? We will answer these and many other questions in our material.
You can also understand the principle of operation of the RCD and its connection options. Expert advice and installation nuances are collected in this material. In addition, videos are posted in the article, from which you will learn about the main errors when connecting and see how the RCD connects in practice.
The purpose and principle of operation of the RCD
Unlike an automatic machine that protects the network from overloads and short circuits, RCDs are designed to instantly detect the presence of leakage current and response by disconnecting the network or a separate electrical line.
Since these two protective devices differ functionally, both must be present in the assembly diagram.
The principle of operation of the RCD is simple: comparing the values of the incoming and outgoing currents and triggering when a mismatch is detected.
A diagram showing the operation of the device in case a phase breakdown occurs. First, the voltage relay (PH) is activated, then the contactor (K)
Inside the case of the automatic device there is a transformer with a core and windings with uniform magnetic flux directed in different directions.
When a leakage current occurs, the output magnetic flux decreases, as a result of which the electric relay trips and opens the power supply. This is possible if a person touches a grounded device and electrical circuit. On average, it takes from 0.2 to 0.4 seconds. We talked about the device and the principle of operation of the RCD here.
There are various types of devices designed for direct or alternating current networks. One of the important technical characteristics that is necessarily present in the marking is the leakage current.
To protect the residents of the house, devices with a nominal value of 30 mA are selected. Where there is an increased risk, for example, bathrooms with high humidity, children’s play rooms, they install an RCD of 10 mA.
A higher rating, such as 100 mA or 300 mA, is designed to prevent fire, as large current leaks can cause a fire. Such devices are mounted as a common introductory RCD, as well as in enterprises and large facilities.
Detailed information on choosing a suitable RCD is described in this article.
The RCD (on the left) should not be confused with the difavtomat (on the right), which combines the functions of a circuit breaker and a protective trip device, that is, it can operate both from overload and from leakage current
AEDT is more compact than a bunch of protective devices and takes up less space in the control cabinet, but when it is triggered it is more difficult to find the cause of the shutdown.
The installation scheme is selected in accordance with the task and the type of network - 1-phase or 3-phase. If it is necessary to protect the whole house or apartment from current leaks, RCDs are installed at the input of the power line.
Single-Phase Protection Options
Manufacturers of powerful household appliances mention the need to install a set of protective devices. Often, the accompanying documentation for the washing machine, electric stove, dishwasher or boiler indicates which devices must be additionally installed in the network.
However, more and more often several devices are used - on individual circuits or groups. In this case, the device in conjunction with the machine (s) is mounted in the shield and connected to a certain line
Considering the number of different circuits, serving sockets, switches, equipment that loads the network as much as possible, we can say that there are an infinite number of RCD connection schemes. In domestic conditions, you can even install a socket with a built-in RCD.
Next, we consider the popular connection options, which are the main ones.
Option # 1 - general RCD for a 1-phase network.
The place of the RCD is at the entrance of the power line to the apartment (house). It is installed between a common 2-pole circuit breaker and a set of circuit breakers for servicing various power lines - lighting and socket circuits, individual branches for household appliances, etc.
If a leakage current occurs on any of the outgoing circuits, the protective device will immediately shut off all lines. This, of course, is its minus, since it will not be possible to determine exactly where the malfunction is
Suppose that a current leak has occurred due to the contact of the phase wire with a metal device connected to the network. The RCD trips, the voltage in the system disappears, and it will be quite difficult to find the cause of the shutdown.
The positive side concerns saving: one device costs less, and takes up less space in the electrical panel.
Option # 2 - general RCD for a 1-phase network + counter.
A distinctive feature of the circuit is the presence of an electricity meter, the installation of which is mandatory.
Protection against current leakage is also connected to the machines, but on the incoming line a meter is connected to it.
If it is necessary to shut off the supply of electricity to an apartment or house, turn off the general automatic machine, and not the RCD, although they are installed nearby and serve the same network
The advantages of this arrangement are the same as the previous solution - saving space on the electrical panel and money. The disadvantage is the difficulty of detecting a leakage current.
Option # 3 - general RCD for a 1-phase network + group RCDs.
The scheme is one of the more complicated varieties of the previous version.
Thanks to the installation of additional devices on each working circuit, protection against leakage currents becomes double. From a security point of view, this is a great option.
Suppose an emergency current leakage occurred, and the connected RCD of the lighting circuit for some reason did not work. Then the general device responds and disconnects all the lines
So that both devices (private and general) do not work immediately, it is necessary to observe selectivity, that is, when installing, take into account both the response time and the current characteristics of the devices.
The positive side of the circuit is that in an emergency one circuit will shut off. It is extremely rare that the entire network is disconnected.
This can happen if an RCD installed on a specific line:
- defective;
- out of order;
- does not match the load.
To avoid such situations, we recommend that you familiarize yourself with the methods of checking the RCD for operability.
Cons - congestion of the electrical panel with a multitude of similar devices and additional expenses.
Option # 4 - 1-phase network + group RCDs.
Practice has shown that the circuit without mounting a common RCD also functions well.
Of course, there is no one protection insurance against failure, but this can be easily fixed by buying a more expensive device from a manufacturer that you can trust.
The scheme resembles an option with general protection, but without installing an RCD for each individual group. It has an important positive point - it is easier to determine the source of the leak.
From the point of view of economy, the wiring of several devices is losing - one common would cost much cheaper.
If the electrical network in your apartment is not grounded, we recommend that you familiarize yourself with the RCD connection diagrams without grounding.
3-phase circuitry
In houses, industrial premises and other structures, there may be a different option for arranging power supply.
So, for apartments, connecting a 3-phase network is uncharacteristic, but to equip a private house, this option is not uncommon. Here, other protection device connection schemes will be used.
Option # 1 - general RCD for a 3-phase network + group RCDs.
For a 380 V network, a 2-pole device is not enough, you need a 4-pole analog: you need to connect 1 zero core and 3 phase conductors.
The circuit is complicated by the equipment of each power line with a separate RCD device. This is optional, but duplicate protection is recommended for additional protection against leakage currents.
The type of wires is important. For a 1-phase network, a standard VVG cable is suitable, while for a 3-phase network, it is recommended to extend a more resistant to ignition VVGng. We wrote about choosing the appropriate type of wire in our other article.
Option # 2 - general RCD for a 3-phase network + counter.
This solution completely repeats the previous one, but an electricity meter has been added to the circuit. Group RCDs are also included in the individual line service system.
Of all the presented circuits, this is the most voluminous in the literal sense, that is, it requires the installation of a large electrical panel with many wires and connected electrical appliances
There is a nuance that applies to any of the presented schemes. If there are several lighting and outlet circuits in the apartment or house, several powerful household appliances requiring the arrangement of separate power lines, it makes sense to install double protection with a common RCD.
In the opposite case, either a common apparatus is sufficient, or one for each circuit.
Instructions for installing an RCD
First you need to choose a place to mount the device. There are 2 options: shield or cabinet. The first resembles a metal box without a lid, mounted at a height convenient for maintenance.
The cabinet is equipped with a door that can be locked. Some types of cabinets have openings so that you can take readings of the meter without opening the door, and turn off the device.
Protective devices are fixed on mounting DIN rails located horizontally. The modular design of automatic machines, difavtomatov and UZO allows to place several pieces on one rail
A neutral wire is always connected to the left terminals at the input and output, and the phase wire to the right. One of the options:
- input terminal N (upper left) - from the introductory machine;
- output N (lower left) - to a separate zero bus;
- input terminal L (upper right) - from the introductory machine;
- output L (lower right) - to group machines.
By the time the protective device is installed, circuit breakers can already be installed on the switchboard. To arrange the arrangement of devices and wires, you may have to rearrange the devices in a certain order.
We present an example of installing an input RCD in an electrical cabinet, where a meter, an input circuit breaker and several circuit breakers for individual circuits - lighting, socket, etc., are already installed.
Image Gallery
Photo from
The dimensions of the shield (ШУЭ, ЩУЭ, ШР) depend on the number of devices placed inside. It is better to choose a product with a small margin for installing new machines and RCDs
On a DIN rail, in one row, a home electricity meter is pre-installed (from left to right), then one input switch and 5 group machines
The best solution for installation, justified by the operation of the devices, is the place between the input machine and other devices serving individual lines (outlet, etc.)
From the lower left terminal, the phase conductor extends to the upper terminal of the middle machine, and zero to the grounding bus, which is located below. The upper phase - from the input machine, zero - from the counter
IEK Metal Switchboard
Set of protective devices before mounting the RCD
Choosing a place for installing an RCD
The procedure for connecting wires to the device
Never connect an RCD at the input - it always follows a common introductory circuit breaker. If a counter is used, the residual current device switches to the third position from the input.
Connection process description:
- install the device on a DIN rail to the right of the machine - just attach it and push it with a little effort until it clicks;
- we stretch the cut and stripped wires from the machine and the zero bus, insert into the upper terminals according to the diagram, tighten the fixing screws;
- in the same way, insert the wires into the lower terminals and tighten the screws;
- test - first turn on the general machine, then RCD, press the "Test" button; when pressed, the device should turn off.
To make sure that the connection is correct, the leakage current is sometimes staged. Take two working wires - the "phase" and "ground", at the same time bring to the base of the lamp. A leak appears and the device should instantly trip.
What mistakes should be avoided?
Before connecting, be sure to double-check the technical specifications of the devices. The rated current must be equal to or higher than the same parameter for the input machine. It is easy to determine the values by marking.
Electricians recommend choosing a protective device a step higher, that is, for a 50A machine, UZO 63A is suitable.
You can correctly calculate the parameters, select the machine and the RCD with the correct rating, but make a small mistake during installation, as a result of which the system will be useless.
For example, newcomers often confuse tires. It should be remembered that I use different buses for the neutral conductor and the ground wire. In addition, for each device, a separate bus is required: for 5 RCDs - 5 buses.
Whatever connection scheme you use, the ground conductor will not participate in it. All terminals are designed for either phase conductor (load) or zero (neutral)
In no case should you confuse the poles N and L. They have lettering on the case, and the wires differ in color, so you need to be careful.
If a false alarm occurs or, on the contrary, the device does not respond, the possible reason is as follows:
- “Phase” and “earth” are connected after the RCD;
- incomplete connection - the N conductor is not inserted into the corresponding terminal;
- “Zero” and “earth” are connected at the outlet;
- confusion between connecting two or more RCDs to electrical installations.
In practice, there are many more errors, since different schemes are used. The more devices involved in the assembly of the electrical panel, the more carefully you need to be when connecting.
Safety rules in the process
Most of the rules are general in nature, that is, they must be applied in the process of any electrical work.
If you decide to equip a distribution board yourself, before installing and connecting an RCD, do not forget:
- turn off the power - turn off the machine at the entrance;
- use wires with the corresponding color marking;
- Do not use metal pipes or fittings in the apartment for grounding;
- install an automatic input switch first.
If possible, it is recommended to use separate devices for lighting lines, sockets, circuits for a washing machine, etc. In the opposite case, installing a common RCD is enough.
To protect children, all electrical installations from the children's room are usually combined into one circuit and equipped with a separate device. Instead of an RCD, you can use a difavtomat
In addition to the characteristics of the devices themselves, the parameters of other elements of the electrical wiring, for example, the cross section of the electric wire, are important. It should be calculated taking into account the constant load.
It is better to connect the wires to each other with the help of terminal blocks, and for connecting to devices - use specially designed, marked terminals, as well as the circuit on the case.
A few practical tips and explanations will help beginners figure out how to choose and connect an RCD in the house or apartment.
Errors when connecting outlets:
About the need and nuances of installing protective devices:
It is not always possible to call a qualified specialist for switchgear equipment. Sometimes machines or RCDs have to be installed independently.
Due to an oversight during installation, an electric shock can occur, therefore it is important to use wiring diagrams, correctly make calculations and follow safety rules.
Are you professionally engaged in electrical work and want to add useful tips or other RCD connection schemes? Maybe you want to supplement our article with recommendations on electrical safety? Write your comments in the block below - your comments will be useful to many home masters.